Is there anyway to take out a heater main point of a 2000 evade durango without acquisition the dash completely off?


You are watching: Heater core for 2000 dodge durango

\"*\"

Hello, Start by disconnecting the battery and also draining the coolant and also if the automobile has AC you will have to evacuate the system below are 2 guides to help walk you through the repair with instruction for how it is excellent on her truck below.https://www.centregalilee.com/articles/re-charge-an-air-conditioner-systemandhttps://www.centregalilee.com/articles/replace-heater-coreCheck the end the diagrams (Below). Please let us recognize if you require anything else to gain the difficulty fixed.
\"*\"

\"*\"

\"*\"

\"*\"

Is it leaking?If not and also not enough hot airShould have it isolated and also flush if leaking and need to have it replaced let me know I will help you through directions
REMOVAL remove the heater-A/C real estate from the vehicle, and remove the real estate cover. Refer to: Heating and Air Conditioning, housing Assembly HVAC, Service and also Repair, Front, prior HVAC Unit Removal and Installation, See: housing Assembly HVAC Service and Repair front Front HVAC Unit Removal and InstallationHeater main point Remove/Install background the heater main point out the the heater-A/C housing.
If walk to change youself suggest great manual prefer Mitchell the you can get from this site because instrument panel demands to be gotten rid of
In the summer I obtain no ac even after ns gas that up and also in the winter I get no heat. That is so bad that some form of foggy problem it coming the end of the vents and steaming increase the windshield. I think its the heater care and I would prefer to know exactly how to change it


See more: What Is The Land Along The Edge Of A Body Of Water Crossword Clue Answers

Heater problem2001 dodge Durango V8 4 Wheel drive Automatic ns would choose to know just how to replace the heater core in the durango.
HEATER equipment - RWD van & VANS -2001 dodge Durango INSTRUMENT dashboard removed & surroundings (Dakota & Durango) 1.Disconnect negative battery cable. Disable wait bag system. Check out AIR BAG system SAFETY post in general SERVICING. Place front wheels in straight-ahead position. Remove door sill trim native both doorways. Eliminate kick panel covers indigenous both political parties of vehicle. Remove mounting bolts for hood release handle. Remove knee bolster. 2.Remove steering shaft trim panel and also support bracket. If equipped, remove tilt steering shaft lever. Eliminate upper and lower shrouds native steering column. Disconnect driver\"s next air bag module. Ease multifunction switch wiring harness connector screw and disconnect native switch. Screw will remain in connector. 3.Disconnect PRNDL cable. Disconnect shift cable native steering column. Remove steering coupler lock pin. Eliminate toe key retaining bolts. Remove steering shaft mounting bolts and remove steering obelisk from vehicle. 4.Remove screw native bulkhead wiring exploit connector and disconnect. Disconnect 2 human body wiring exploit connectors, situated next to bulkhead connector. Disconnect 3 wiring exploit connectors, located nearest come dash dashboard junction block. Disconnect brake irradiate switch. If equipped, disconnect behind Wheel Anti-Lock (RWAL) brake module, situated near steering obelisk support brackets. 5.Disconnect plastic retainer clip indigenous parking brake link rod, situated at back of parking brake relax handle. Eliminate rod finish from parking brake handle. Remove instrument panel center support bracket. Unplug vacuum harness connector situated at left end of heater assembly housing. Disconnect wait Bag regulate Module (ACM) connector. 6.Remove glove box. Reach with glove box opening and disconnect antenna coaxial cable. Disconnect blower motor connector located over glove crate opening, close to support brace because that heater assembly housing. Disconnect radio soil strap. Loosen instrument dashboard roll-down parentheses bolts about 2 transforms (bolts are situated at reduced corners, on both sides of instrument panel) . Eliminate 5 bolts across top the dash panel, at base of windshield, removing facility screw last. 7.Roll down instrument panel and install a temporary assistance hook the is about 18\" (457 mm) in length. Download hook from center hole in instrument dashboard to facility hole of dash panel. Pull reduced instrument panel outside until both roll-down clip bolts space in slotted roll-down pivot position . Tool panel must now it is in supported and away from firewall. 8.Disconnect 2 body wiring harness connectors, located on a bracket near right end of instrument panel. Disconnect blower engine resistor. Disconnect temperature regulate cable from heater assembly housing and remove indigenous housing. Disconnect defrost duct versatile hose from heater assembly housing. 9.Ensure every electrical and also vacuum connectors space disconnected and instrument dashboard is free and clear for removal. Through the aid of an assistant, eliminate temporary assistance hook. Lift tool panel off of roll-down clip bolts and remove indigenous vehicle. 10.To install, reverse removal procedure. Ensure every wiring and also hoses room clear and not pinched. Adjusting temperature control cable. Tighten bolts and also nuts come specification.. Permit air bag system. 1.Disconnect an adverse battery cable. Ensure prior wheels are in a straight-ahead position and also steering wheel is in LOCKED position. Disable wait bag system. Eliminate Air Bag manage Module (ACM) and also bracket native floor panel transmission tunnel. Drainpipe cooling system. 2.Remove left and also right cowl next inner trim panels. Remove knee bolster/steering shaft cover. Remove hood release and also parking brake release handle bolts from lower instrument dashboard support. 3.Disconnect driver\"s side air bag connector at reduced left edge of instrument panel. If equipped, disconnect overdrive lock-out switch wiring exploit connector from tool panel wire harness near instrument panel reduced reinforcement. 4.Pull PRNDL cable and also twist to eliminate from place arm. Push tab on bottom that cable retainer upward, climate squeeze sides to eliminate retainer from column. If equipped, eliminate tilt lever. Eliminate both upper and lower shrouds indigenous column. Remove reduced fixed shaft shroud. Loosen multifunction move connector screw. Screw will remain in connector. 5.Ensure steering wheel is in LOCKED position. Remove staying steering column electric connectors. Remove air bag wiring exploit from steering tower wiring trough. Eliminate wiring trough from steering column. Remove steering pillar as one assembly native vehicle. 6.From driver\"s side of instrument panel, disengage parking brake release affiliation rod indigenous parking brake mechanism. Disconnect instrument dashboard wiring exploit from parking brake mechanism. Disconnect 3 wiring exploit bulkhead connectors located closest to dash panel. 7.Disconnect instrument panel left side wiring exploit connectors. Remove screw from facility of headlight and also dash-to-instrument dashboard (bulkhead) connector, and also disconnect connector. Disconnect instrument panel-to-door wiring harness. Disconnect instrument panel to stoplight switch connector. Disconnect vacuum harness because that heater system. 8.If car is equipped with Infinity sound system, disconnect Infinity wiring harness connector indigenous instrument panel harness connector the is secured come bulkhead connector. 9.From passenger\"s side of tool panel, disconnect radio antenna coaxial cable connector. Loosen right and also left instrument dashboard roll-down clip bolts about .50\" (13 mm) . Removing facility screw last, remove 5 bolts holding optimal of instrument dashboard to height of dash panel. 10.Roll instrument dashboard downward and install a temporary assistance hook to center hole of dash panel. Assistance hook need to support instrument panel in rolled under position, around 18\" (457 mm) far from dash panel. Disconnect staying wiring exploit connectors. With the help of an assistant, eliminate temporary hook and also lift instrument panel from vehicle. 11.To install, reverse removal procedure Ensure every wiring and also hoses room clear and not pinched. Tighten bolts and also nuts to specification . Allow air bag system.

\"*\"